Coir Logs: Sizes, Density and How to Specify Them
Coir logs are tightly packed rolls of coconut fibre held in coir netting. They slow water, trap sediment and give plants a place to root while a bank or slope stabilises. Here is what the sizes and density figures mean, and what to put in a spec before you order.
By Anthony Alexander, Regional Operations Head, Avee Cocoseller · Published November 2026


Short answer: a coir log (also sold as a coir roll, fibre roll or bio log) is a cylinder of coconut husk fibre compressed inside a coir-twine net. The common sizes are 12, 16 and 20 inches in diameter and 10 or 20 feet long. They come in two densities, about 7 lb per cubic foot for standard logs and 9 lb per cubic foot for high-density logs. Use standard density for ponds, swales and gentle streams, and high density where waves or faster water hit the bank. Logs last roughly two to five years in the field, long enough for planted vegetation to take over.
Coir logs are a soft-engineering tool. They are not a replacement for riprap or an engineered wall on a high-energy site, but on the right bank they cost less, need no heavy machinery and leave nothing behind when they break down.
Standard sizes
| Diameter | Common lengths | Typical use |
|---|---|---|
| 6–9 in (15–23 cm) | 10 or 20 ft | Usually sold as coir wattles: small slopes, swales, inlet and perimeter sediment control |
| 12 in (30 cm) | 10 or 20 ft | Pond edges, small streams, slope breaks, garden-scale banks |
| 16 in (40 cm) | 10 or 20 ft | Streambank toe protection, larger ponds |
| 20 in (50 cm) | 10 or 20 ft | Lakeshores, bayshores and higher-energy streambanks |
Most suppliers build logs in 10-foot and 20-foot lengths, and some state transportation specifications describe lengths in 10- or 20-foot increments. Other lengths and diameters can usually be made to order with extra lead time.
Standard vs high density
Density is how tightly the fibre is packed, and it is the number that matters most after diameter.
- Standard density, about 7 lb/ft³ (around 112 kg/m³): recommended for low-energy sites such as ponds and slow streams, and for sediment control on construction sites. It is lighter, cheaper and easier to plant into.
- High density, about 9 lb/ft³ (around 144 kg/m³): recommended for higher-energy sites such as lakes, bayshores and streambanks. It holds its shape longer under wave action and current.
Check the specification you are working to. Some state DOT specifications set a minimum density, for example a minimum of 9 lb/ft³ for coir log sediment barriers, and some set a weight per linear foot for each diameter. A 20-inch high-density log weighs roughly 15 lb per foot, so a 10-foot log is a two-person lift.
What goes into a good coir log
- Fill: 100% coconut husk fibre, cleaned. Mattress-grade (brown) coir fibre is the usual core. Ask how much pith and dust the fill contains; loose pith washes out and leaves voids.
- Netting: coir twine, typically a 2 × 2 in mesh. Many specifications ask for multi-ply coir twine and name a minimum tensile strength. Avoid synthetic netting if the project calls for a fully biodegradable product, and note that burlap is not accepted in some specifications.
- Closure: ends tied with coir twine so the fill cannot spill during handling.
- Weight per foot: the easiest field check that the density on the paperwork is real. Weigh a log and divide by its length.
Where coir logs work, and where they don’t
They work best where the main problem is surface erosion and low-to-moderate flow:
- Toe protection along streambanks and pond edges
- Lake and bay shorelines with moderate wave action (high-density logs)
- Slope breaks on graded embankments, to shorten the slope and catch sediment
- Sediment barriers and swales on construction sites
- Wetland and riparian restoration, where the log doubles as a planting bed for plugs
They are the wrong tool for deep slope failures, steep high-velocity channels or anything that needs a permanent structural wall. On those sites a coir log can still be part of a design, for example on top of rock toe protection, but it should not be the only measure.
How coir logs are installed
- Prepare a trench. Excavate a shallow trench along the line of the log so it beds into the soil rather than sitting on top. Water running under a log is the most common reason one fails.
- Place the log firmly against the bank, butting log ends tightly together or lacing them with coir twine.
- Stake it. Drive untreated wooden stakes through or alongside the log. Around five or six 2 × 2 in stakes per 10-foot log is a common starting point, with more on steep or soft ground. Some specifications cross-lash the log to notched stakes with coir twine and limit how far stakes stand above the log.
- Backfill and plant. Backfill behind the log, then plant plugs or live cuttings into the fibre and the bank behind it. The roots are what stabilise the site once the coir breaks down.
Always follow the project drawings and the manufacturer’s or agency’s installation detail where one exists.
How long do coir logs last?
Most suppliers quote a functional life of roughly two to five years, and some say up to three. The range depends on density, how wet the log stays, water energy and climate. That is by design: the log only has to hold until vegetation is established. As it breaks down, the fibre becomes organic matter in the soil.
A specification checklist
Before you request quotes, write down:
- Diameter and length of each log, and the total linear feet
- Density (lb/ft³ or kg/m³) and minimum weight per linear foot
- Fill material and cleaning standard
- Netting material, mesh size and twine ply or tensile strength
- Whether logs must be pre-drilled or slotted for stakes or plants
- Any DOT, municipal or agency specification the logs must meet
- Delivery location, unloading equipment and the date you need them on site
Ask every supplier to quote against the same list, so you are comparing the same density and netting rather than the same name.
Coir logs vs coir wattles vs straw wattles
Coir wattles are smaller, usually 6 to 9 inches in diameter, and are used for perimeter and inlet sediment control and small slopes. Coir logs are larger and heavier and are used where water acts on the bank. Straw wattles cost less and break down within a season or two, which suits short construction projects but not long-term bank stabilisation.
Common questions
Is a coir log the same as a fibre roll or bio log?
Usually, yes. “Coir log”, “coir roll”, “coir fibre roll” and “bio log” are used for the same product. Check the fill: some “bio logs” are made from straw, wood fibre or compost rather than coir.
How many stakes do I need for a 10-foot coir log?
Five or six is a common starting point. Use more on steep slopes, soft soil or sites exposed to waves.
Can I plant into a coir log?
Yes. Plugs of riparian or wetland plants can be pushed into the fibre, often at about two per linear foot, and pre-drilled logs make this faster.
Are coir logs fully biodegradable?
Logs made with coir fill and coir-twine netting are. Check for synthetic netting or closures if the project requires a plastic-free product.
What is coir fibre, and how is it different from coco peat?
Coir fibre is the long, strong strand from the coconut husk; coco peat is the fine, spongy pith around it. Logs, wattles and erosion blankets use the fibre. For more detail see what coconut coir fibre is and how it is graded.
